2189123 Wilo United Kingdom Sales

Stratos GIGA B 80/1-13/1.9 High-efficiency block pump with EC motor of the Efficiency class IE5 in accordance with IEC 60034-30-2 and electronic Power adjustment in dry runner design. The pump is designed as a single-stage low-pressure centrifugal pump with flange connection and mechanical seal. The Stratos GIGA B is primarily for pumping heating water (in accordance with VDI 2035), Cold water and water-glycol mixtures without abrasive substances in heating, air conditioning and cooling systems designed. Construction: - Single-stage low-pressure centrifugal pump with undivided shaft in Block design including foot on pump housing - Flange and housing dimensions according to EN 733 - PN 16 flanges - drilled according to EN 1092-2 - Pressure measurement connections (R 1/8) for attached Differential pressure transmitter (version... -R1 without differential pressure sensor) - pump housing and motor flange as standard with cataphoresis coating - Mechanical seal for water delivery up to Tmax. = +140°C. Up to T = +40°C, a glycol admixture of 20% to 40% is Volume percentage allowed. In the case of water/glycol mixtures with Glycol proportions > 40% to max. 50% by volume and one Media temperature from > + 40°C to max. +120°C or others Media other than water is an alternative Provide a mechanical seal. - Supply voltages: 3~480 V + -10% 50/60 Hz; 3~440 V +- 10% 50/60 Hz; 3~400 V + -10% 50/60 Hz; 3~380 V - 5% +10% 50/60 Hz accessories: - consoles for foundation mounting - 0-10 V differential pressure sensor sets for pumps in this version ... -R1 - IR monitor - IR stick - IF module PLR - LON IF module - Modbus IF module - BACnet IF module - IF module CAN Standard equipment: - Green button hand control panel for: - pump on/off - Choice of control mode: Δp-C (differential pressure constant), Δp-V (variable differential pressure), PID control, n-constant (controller) - Setpoint or speed setting - Configuration of operating parameters - Error acknowledgement - Pump display to display: - Control type - Target value (e.g. differential pressure or speed) - Error and warning messages - Actual values (e.g. power consumption, actual sensor value) - Operating data (e.g. operating hours, energy consumption) - Status data (e.g. status of the SSM and SBM relay) - Device data (e.g. pump name) - Operating mode (only for downpipe use: main /standby mode, parallel operation) Additional Features: - Analog interfaces 0-10 V, 2-10 V, 0-20 mA, 4-20 mA, integrated double pump management for use in Down pipe, two configurable alarm relays for operating and Fault messages, configurable error behavior tailored to heating and air-conditioning applications, pump access lock, integrated full motor protection (KLF) with electronic trigger, standard condensate drain holes in the motor housing (with delivery sealed), IR interface for wireless communication with the Wilo-IR Monitor control and service device and Wilo-IR stick, slot for Wilo IF modules Modbus, BACnet, CAN, PLR, LON for connection to building automation. Operational data Delivery medium: water 100% Media temperature: 20.00 °C Requested flow rate: 69.00 m³/h Requested delivery height: 6.00 m Media temperature: -20... 140 °C Ambient temperature: 0... 40 °C Maximum operating pressure: 16 bar Design note: 16 bar to 120 °C, 13 bar to 140 °C Minimum efficiency index (MEI): ≥ 0.7 propulsion Power supply: 3~400V/50 Hz Motor efficiency class: IE5 power consumption: 2520 W Rated motor power: 2,3 kW Current (max): 4.7 A Max. speed: 2200 rpm Interference emission: EN 61800-3 Immunity to interference: EN 61800-3 Insulation class: F Motor protection class: IP55 Motor protection: KLF integrated materials Pump housing: 5.1301, EN-GJL-250 KTL coated Impeller: PPS-GF40 Wave: 1.4542 Shaft seal: AQ1EGG Lantern: 5.1301, EN-GJL-250 KTL coated Installation dimensions Suction side pipe connection: DN 100, PN 16 Pressure-side pipe connection: DN 80, PN 16